Humans have the advantage of bipedal locomotion, which allows them to have free use of their hands. However, when it comes to running, there is a physical constraint that limits the use of only the leg muscles. Considering that even cheetahs, known for their fast running speed, utilize all four limbs, it can be hypothesized that if humans could utilize the muscles of other body parts in addition to the legs while running, they could achieve faster running speeds[1].<\/p>\n\n\n\n
Based on this idea, we aimed to utilize the muscular strength of the arms, which play a role in maintaining balance and facilitating smooth leg movements during running. The objective of this study was to develop an auxiliary device that attaches to the shoes and transfers the muscular strength of the arms to the soles, generating additional propulsive forces to increase running speed.<\/p>\n<\/div>\n<\/div>\n<\/div>\n\n\n\n
While there are devices like roller skates that can increase human running speed, such wheeled devices cannot be used on uneven surfaces like dirt roads. However, the device developed in this study can maintain the typical running motion even on uneven surfaces and effectively increase running speed.<\/p>\n\n\n\n
Furthermore, the device assists running without requiring additional external power and utilizes muscles from body parts that were not previously involved in running. This highlights the significance of the device as an enhancement tool that relies solely on human power to improve running performance.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n\n
The designed device, named Wire-driven Running Reinforcement Shoes (WRRS), utilizes wires as power transmission elements to enhance running performance.<\/p>\n\n\n\n
The components of the WRRS, which are attached to the sides of the shoes, can be divided into three main parts. These include the wire and pulley mechanism for transferring arm power to the ankles, the internal gear mechanism that amplifies the output torque of the wire, and the pad section on the shoe sole that generates propulsive forces by pushing off the ground with the amplified rotational output.<\/p>\n<\/div>\n\n\n\n To maintain balance in the body, the hands and feet move in opposite directions while running. As the feet push off the ground, the wrists naturally move away from the ankles, pulling the connected wire. In this process, a mechanism has been devised to transmit rotational output to the shoe sole through a gear box located in the shoe, thereby obtaining propulsion force.<\/p>\n<\/div>\n\n\n\n When setting the wire pulling as the input and the rotation of the shoe pad as the output, increasing the gear ratio of the gear box is crucial for achieving high propulsion force. To determine the specific requirements for the gear output ratio, the necessary rotation angle of the shoe pad and the constraints on the wire length that can be pulled during running motion need to be established.<\/p>\n\n\n\n The moment when the wire is most pulled corresponds to the moment when the distance between the ankle and wrist is the greatest, which is similar to the toe-off moment. Additionally, this distance is minimized during foot-strike[2]. Therefore, the length difference between foot-strike and toe-off was measured. Based on measurements taken during running motion, the length of the pulled wire ranged from 18cm to 20cm, and this range was used to define the operational range.<\/p>\n\n\n\n The flexion angle of the shoe is known to have an impact on propulsion force, with the highest propulsion force observed at a moderate flexion angle of 50 degrees[3]. Considering this, the output rotation angle of the pad was set between 20 degrees and 30 degrees. Excessive rotation angle can lead to instability in posture at the flexion point of the foot.<\/p>\n<\/div>\n\n\n\n The internal gear box of the main body was designed by modifying the structure of a Planetary Gear Train[4].<\/p>\n\n\n\n In order to maintain high gear output for supporting body weight and pushing against the ground, while also ensuring compatibility with shoe attachment, the diameter of the gear box needs to be small. To achieve this, a Double Layer Planetary Gear system was designed, where the Planetary Gear is arranged in two layers, resulting in a decreased diameter for the same gear ratio.<\/p>\n\n\n\n Comparing to the gear ratio of 5.8:1 used in the Cheetah Robot’s actuators developed at MIT[5], assuming the same diameter of the disk, the Double Layer Planetary Gear structure achieves a gear ratio output of 1:10.5 with the same number of gear engagements, allowing for approximately 1.8 times higher torque compensation.<\/p>\n\n\n\n Figures 2 and 3 depict cross-sectional views of the Double Layer Planetary Gear. It shows the difference from conventional gear systems as the Planetary Gear is divided into two layers, providing rotational output through the Ring gear.<\/p>\n<\/div>\n\n\n\n Considering the high precision and stress concentration of gears, it was determined that 3D printing has limitations for producing them. Therefore, a spur gear was chosen, taking into account the bending and torsional loads analyzed. The gear was selected based on the Standard Gear with a module of 1.0mm, considering the compatibility with 3D printed parts and choosing the specifications with keyway and hub.<\/p>\n<\/div>\n\n\n\n To operate the gear mechanism with the wire, a pulley component was designed. A rubber band was utilized to reset the pulley to its reset position when transitioning from the toe-off motion to the foot-strike motion. To prevent malfunction caused by the wire and rubber band overlapping, the pulley was positioned on the opposite side of the pulley shaft to allow simultaneous winding and unwinding. As a result, the likelihood of the wire and rubber band getting tangled was reduced, and the generation of moments was brought closer to the bearing for stable rotation.<\/p>\n<\/div>\n\n\n\n To analyze the gear’s motion more accurately, the specific rotation conditions of the pulley were determined, and the operation was simulated using the Simulation program within Solidworks. Based on the calculated angular position of the pulley due to wire tension, angular velocity and acceleration were set using a 3rd order polynomial for the simulation.<\/p>\n<\/div>\n\n\n\n First, the entire model was created using the SOLIDWORKS program, and the gear part of the overall model was analyzed using the ANSYS analysis program. The maximum allowable moment and deformation at that point were compared for two different materials: PLASTIC (ABS) and SUS 304. If the applied external force is smaller than the yield strength of the material, elastic deformation occurs, and the material returns to its original shape. However, if the applied external force is stronger than the yield strength, the material undergoes plastic deformation and does not return to its original shape. Therefore, the maximum allowable stress for each material was calculated by dividing the yield stress by a safety factor of 1.25 (maximum stress = yield stress \/ safety factor). The maximum allowable moment, which occurs when the maximum stress is reached, was also calculated.<\/p>\n<\/div>\n\n\n\n To fabricate the model, the Mark2 3D printer model from Markforged was utilized for 3D printing.<\/p>\n<\/div>\n<\/div>\n\n\n\n2.1.1 Mechanism<\/h5>\n\n\n\n
2.1.2 Design Constraints and Objectives<\/h5>\n\n\n\n
2.1.3 Gear box : Planetary Gear Train<\/h5>\n\n\n\n
2.1.4 Wire Output Section<\/h5>\n\n\n\n
2.2 Analysis<\/h4>\n\n\n\n
2.2.1 Simulation<\/h5>\n\n\n\n
2.2.2 Ansys Analysis<\/h5>\n\n\n\n
2.2.2.1 Plastic Material<\/h6>\n\n\n\n
\n
2.2.2.2 SUS 304 Material<\/h6>\n\n\n\n
\n
<\/td> Plastic (ABS)<\/td> SUS 304<\/td><\/tr> Yield Stress (Pa)<\/td> 2.744\u00d7107<\/sup><\/td> 2.5\u00d7109<\/sup><\/td><\/tr> Safety Factor<\/td> 1.25<\/td> 1.25<\/td><\/tr> Maximum Allowable Stress (Pa)<\/td> 2.1952\u00d7107<\/sup><\/td> 2.0\u00d7109<\/sup><\/td><\/tr> Maximum Allowable Moment (Nm)<\/td> 1.35<\/td> 120<\/td><\/tr> Deformation (m)<\/td> 5.89\u00d710-5<\/sup><\/td> 5.50\u00d710-7<\/sup><\/td><\/tr><\/tbody><\/table> 2.3 Manufacturing<\/h4>\n\n\n\n
2.3.1 3D Printing<\/h5>\n\n\n\n